Choose a state

C-4 (CR-4) Boilers, Steamfitting and Process Piping (Commercial) (2023-06-08)

Installation, alteration, and repair of steam and hot water systems and boilers, including chimney connections, flues, refractories, burners, piping, fittings, valves, thermal insulation, and accessories; fuel and water lines from the source of supply to boilers; process and specialty piping and related equipment; pneumatic and electrical controls. If necessary, a new circuit may be added to the existing service panel or sub-panel. Excluded is the installation of a new service panel or subpanel.

50 Questions
70% Minimum Passing Score
120 Minutes Time Allowed

The reference material listed below was used to prepare the questions for this examination.  The examination may also contain questions based on trade knowledge or general industry practices. Except for Code books, you can base your answers on later editions of references as they become available.  For Code questions, the examinations will be based only on the edition of the Code book that is listed.

Sign Up for Exam Prep
These products apply to test outline dated 2023-06-08

Click Here to View the Candidate Information Bulletin Click Here to View the Candidate Information Bulletin



Open Book These books are allowed while taking your test.
Closed Book These books are for pre-test study only and are not available for use during the test.
In Stock These books are currently in stock.
Out of Stock These books are currently out of stock.

  • Open Book Out of Stock

    International Fuel Gas Code 2009

    Publication Year: 2009

    $0.00

    1 - Scope and Administration, 2 - Definitions, 3 - General Regulations, 4 - Gas Piping Installations, 5 - Chimneys and Vents, 6 - Specific Appliances, 7 - Gaseous Hydrogen Systems, 8 - Reference Standards, Appendix A - Sizing and Capacities of Gas Piping, Appendix B - Sizing of Venting Systems Serving Appliance Equipped with Draft Hoods, Category 1 Appliances and Appliances Listed for Use with Type B Vents, Appendix C - Exit Terminals of Mechanical Draft and Direct-vent Venting Systems, Appendix D - Recommended Procedures for Safety Inspection of an Existing Appliance Installation.

    *This title is currently offered only as a Digital Copy. Please CLICK HERE to purchase the digital copy directly through the publisher*

  • Closed Book In Stock

    IPT's Pipe Trades Handbook

    Publication Year: 1991

    $45.00

    IPT's Pipe Trades Handbook is North America's most popular and widely used reference book. It was revised in 2006 to 534 pages. Used for on-the-job reference as well as numerous training and apprenticeship programs.

  • Open Book Out of Stock

    International Mechanical Code Turbo Tabs 2009

    $12.93

    Flip through the 2009 I-Codes series and find frequently used sections fast! You'll be surprised how easy it is to find what you are looking for. These tabs were created by industry experts who carefully identified the most referenced sections in the code.

  • Open Book Out of Stock

    International Mechanical Code 2009

    Publication Year: 2009

    $0.00

    For the most current mechanical codes that address the design and installation of the most current mechanical systems, use the 2009 International Mechanical Code?. Designed to provide comprehensive regulations for mechanical systems and equipment, it includes coverage of HVAC, exhaust systems, chimneys and vents, ducts, appliances, boilers, water heaters, refrigerators, hydraulic piping, and solar systems. This valuable reference uses prescriptive- and performance- related provisions to establish minimum regulations for a variety of systems.

     

    *This title is currently offered only as a Digital Copy. Please CLICK HERE to purchase the digital copy directly through the publisher*

  • Open Book Out of Stock

    International Fuel Gas Code Turbo Tabs 2009

    Publication Year: 2009

    $12.93

    Flip through the 2009 I-Codes series and find frequently used sections fast! You'll be surprised how easy it is to find what you are looking for. These tabs were created by industry experts who carefully identified the most referenced sections in the code.

  • Closed Book In Stock

    Low Pressure Boilers 5th Edition

    $120.00

    Low Pressure Boilers is the leading resource for preparing for low pressure boiler operator and facility operating engineer licensing. This textbook provides a comprehensive overview of the latest information on the safe and efficient operation of low pressure steam and hot water boilers, cooling systems, and related equipment. Each chapter is divided into sections to aid comprehension of key concepts. To assist with preparing for a licensing exam, a separate chapter with test-taking tips and a sample exam is included.

  • Open Book In Stock

    Code of Federal Regulations, 29 CFR Part 1926 (OSHA) 2024

    Publication Year: 2024

    $32.00

    The OSHA 29 CFR 1926 Construction Regulations book offers convenient access to vital safety guidance for both employers and employees, aiding in the prompt identification of potential hazards on any job site. Its user-friendly design features a two-color layout, simplifying navigation and comprehension of regulations. It encompasses all 1926 regulations, along with 1903 regulations on inspections, citations, and penalties, as well as 1904 regulations concerning record keeping and reporting of occupational injuries and illnesses. Additionally, select 1910 regulations relevant to construction industries are included. The book highlights regulation changes between releases and provides easy-to-access OSHA interpretations, aiding in clarity and reference. Essential documents such as OSHA Form 300 and the Cancer Policy are incorporated. In-Cite Referencing to applicable 1910 regulations is provided for further context. Lastly, the book outlines the Most Frequently Cited Standards preceding relevant Subparts, enhancing its utility as a comprehensive safety resource.

  • Open Book In Stock

    Blank Quick Reference Tabs

    $13.00

  • Closed Book In Stock

    Modern Hydronic Heating & Cooling for Residential and Light Commercial Buildings 4th Edition

    4th Edition

    $250.00

    From simple applications to multi-load and multi-temperature systems, this one-of-a-kind, comprehensive text prepares readers to use the latest hydronics to create systems that deliver the ultimate in comfort, reliability and energy efficiency. Abundantly illustrated with product and installation photos and hundreds of detailed, full-color schematics, MODERN HYDRONIC HEATING, Fourth Edition, transforms engineering-level design information into practical applications useful for technical students and heating professionals alike. The revised edition features the latest design and installation techniques for residential and light commercial hydronic systems, including use of renewable energy heat sources such as air-to-water and geothermal heat pumps, hydraulic separation, variable speed circulators, distribution efficiency, heat exchangers, buffer tanks, heat metering, hydronic cooling, system balancing and proper system documentation. Anyone involved in the heating trade will benefit from this preeminent resource of the North American heating industry, which is equally well-suited for formal education courses, self-study or on-the-job reference.