B-1 Limited Gas and Oil Burner Contractor

In order to comply with the provisions of Public Act 99-253 and Public Act 00-128, and the regulations promulgated there under concerning Sheetmetal Work; "any person holding a license as defined within section 20-330 ( 5 ) of the Connecticut Statutes, may perform sheetmetal work' as it pertains to the type of license that such person holds." The examinations contained within this Heating, Piping, and Cooling Candidate Information Bulletin have the appropriate sheetmetal related questions pertaining to each examination type as defined in Section 20-330 ( 13 ) of the Connecticut General Statutes.

50 Questions
Minimum Passing Score of 70%
Time Allowed - 2 Hours

The reference material listed below was used to prepare the questions for this examination. The examination may also contain questions based on trade knowledge or general industry practices. Except for Code books, you can base your answers on later editions of references as they become available. For Code questions, the examinations will be based only on the edition of the Code book that is listed.

Open Book In Stock

International Fuel Gas Code 2021

Publication Year: 2021

$100.00

2021 International Fuel Gas Code addresses the design and installation of fuel gas systems and gas-fired appliances through requirements that emphasize performance.
Open Book In Stock

International Residential Code for One and Two Family Dwellings Turbo Tabs 2021

$15.00

Flip through the 2021 I-Codes series and find frequently used sections fast! You'll be surprised how easy it is to find what you are looking for. These tabs were created by industry experts who carefully identified the most referenced sections in the code.

Soft Cover Tabs Contain: Clear plastic, self-adhesive tabs that have the key sections of the code printed on them in an easy-to-read format. The soft cover tabs can also be used in the 2021 I-Code Commentary series.
Open Book In Stock

International Fuel Gas Code Turbo Tabs 2021

Publication Year: 2021

$20.00

Flip through the 2021 I-Codes series and find frequently used sections fast! You'll be surprised how easy it is to find what you are looking for. These tabs were created by industry experts who carefully identified the most referenced sections in the code.

Loose Leaf Tabs Contain: Full-page inserts tabs that have the key code sections printed on them in an easy-to-read format.

Soft Cover Tabs Contain: Clear plastic, self-adhesive tabs that have the key sections of the code printed on them in an easy-to-read format. The soft cover tabs can also be used in the 2021 I-Code Commentary series.
Open Book In Stock

International Mechanical Code 2021

$100.00

Establishes minimum regulations for mechanical systems using prescriptive and performance-related provisions. The IMC was developed with broad-based principles that make possible the use of new materials, methods and design.

Important changes in the edition include:

Clothes dryer exhaust terminals required to be at least 3 feet from any opening into a building.
Polyurethane spray-applied foam on the exterior of ducts in attics and crawl spaces required to meet specific smoke and flame index limits.
Fire and smoke dampers must be provided with approved access for inspection and maintenance.
Refrigerant tables updated to include new refrigerants.
Addition of condensate termination identification markings and discharge restrictions.
Approved factory-built combination intake/exhaust terminations permitted, relaxing separation requirement.
30% reduction in minimum mechanical ventilation for whole-house balanced ventilation systems.
Continuous operation requirement for manicure and pedicure station exhaust systems.
Grease duct horizontal cleanout required within 3 feet of a horizontal discharge fan.
Open Book In Stock

NFPA 31: Standard for the Installation of Oil-Burning Equipment 2011

2011 Edition

$149.00
Open Book Out of Stock

NFPA 54: National Fuel and Gas Code Handbook 2012 Edition

Publication Year: 2012

$150.00

Fully updated and featuring new full-color photos, NFPA®'s 2012 National Fuel Gas Code Handbook explains technical NFPA 54 rules and fuel gas safety concepts -- so you're prepared to answer questions from employees and owners; and verify fuel gas piping, appliance, and venting jobs are in compliance.The only complete guide to the 2012 NFPA 54 Code, the Handbook is written by industry authorities including Franklin Switzer, Jr., President of S-afe, Inc., NFPA Senior Engineer Denise Beach, Paul Cabot of the American Gas Association, and John Roberts from Rimkus Consulting Group.
Open Book In Stock

NFPA 58: Liquefied Petroleum Gas Code 2014

Publication Year: 2014

$150.00

Liquefied Petroleum Gas Code provides minimum safety requirements for all liquefied petroleum gas (propane) installations, from small cylinders installed at residences to large bulk storage facilities that can exceed 100,000 gallons. The code includes minimum requirements for safe handling during LP gas transfer, including operator qualifications, maximum filling quantity in containers, and pre-transfer inspections to ensure containers are fit for continued service.
Open Book In Stock

International Residential Code for One and Two Family Dwellings 2021

Publication Year: 2021

$150.00

This comprehensive code comprises all building, plumbing, mechanical, fuel gas and electrical requirements for one- and two-family dwellings and townhouses up to three stories.

**In Stock**
Open Book In Stock

International Mechanical Code Turbo Tabs 2021

$15.63

Flip through the 2021 IMC and find frequently used sections fast! You'll be surprised how easy it is to find what you are looking for. These tabs were created by industry experts who carefully identified the most referenced sections in the code.

Loose Leaf Tabs Contain: Full-page inserts tabs that have the key code sections printed on them in an easy-to-read format.

Soft Cover Tabs Contain: Clear plastic, self-adhesive tabs that have the key sections of the code printed on them in an easy-to-read format.